If you need urgent consulting help click here

EFM32 Pearl Gecko Starter Kit

Overview

The EFM32 Pearl Gecko Starter Kit EFM32PG-STK3402A contains an MCU from the EFM32PG family built on an ARM® Cortex®-M4F processor with excellent low power capabilities.

Fig. 102 EFM32PG-SLSTK3402A (image courtesy of Silicon Labs)

Hardware

• Advanced Energy Monitoring provides real-time information about the energy consumption of an application or prototype design.

• Ultra low power 128x128 pixel Memory-LCD

• 2 user buttons, 2 LEDs and a touch slider

• Humidity, temperature, and inductive-capacitive metal sensor

• On-board Segger J-Link USB debugger

For more information about the EFM32PG SoC and EFM32PG-STK3402A board:

• EFM32PG Website

• EFM32PG12 Datasheet

• EFM32PG12 Reference Manual

• EFM32PG-STK3402A Website

• EFM32PG-STK3402A User Guide

• EFM32PG-STK3402A Schematics

Supported Features

The efm32pg_stk3402a board configuration supports the following hardware features:

Interface	Controller	Driver/Component
MPU	on-chip	memory protection unit
NVIC	on-chip	nested vector interrupt controller
SYSTICK	on-chip	systick
COUNTER	on-chip	rtcc
FLASH	on-chip	flash memory
GPIO	on-chip	gpio
UART	on-chip	serial port-polling; serial port-interrupt
I2C	on-chip	i2c port-polling
WATCHDOG	on-chip	watchdog
TRNG	on-chip	true random number generator

The default configuration can be found in the defconfig file:

boards/arm/efm32pg_stk3402a/efm32pg_stk3402a_defconfig

The default configuration when building for this EFM32JG12B SoC can be found in another defconfig file:

boards/arm/efm32pg_stk3402a/efm32pg_stk3402a_defconfig_jg

Other hardware features are currently not supported by the port.

EFM32 Jade Gecko SoC

The EFM32 Pearl Gecko Starter Kit EFM32PG-STK3402A can also be used to evaluate the EFM32 Jade Gecko SoC (EFM32JG12B). The only difference between the Pearl Gecko and the Jade Gecko is their core. The Pearl Gecko contains an ARM® Cortex®-M4F core, and the Jade Gecko an ARM® Cortex®-M3 core. Other features such as memory and peripherals are the same.

Code that is built for the Jade Gecko also runs on an equivalent Pearl Gecko.

To build firmware for the Jade Gecko and run it on the EFM32 Pearl Gecko Starter Kit, use the board efm32pg_stk3402a_jg instead of efm32pg_stk3402a.

Connections and IOs

The EFM32PG12 SoC has twelve GPIO controllers (PORTA to PORTL), but only four are currently enabled (PORTA, PORTB, PORTD and PORTF) for the EFM32PG-STK3402A board.

In the following table, the column Name contains pin names. For example, PE2 means pin number 2 on PORTE, as used in the board’s datasheets and manuals.

Name	Function	Usage
PF4	GPIO	LED0
PF5	GPIO	LED1
PF6	GPIO	Push Button PB0
PF7	GPIO	Push Button PB1
PA5	GPIO	Board Controller Enable EFM_BC_EN
PA0	UART_TX	UART TX Console VCOM_TX US0_TX #0
PA1	UART_RX	UART RX Console VCOM_RX US0_RX #0
PD10	UART_TX	EXP12_UART_TX LEU0_TX #18
PD11	UART_RX	EXP14_UART_RX LEU0_RX #18
PC10	I2C_SDA	ENV_I2C_SDA I2C0_SDA #15
PC11	I2C_SCL	ENV_I2C_SCL I2C0_SCL #15

System Clock

The EFM32PG SoC is configured to use the 40 MHz external oscillator on the board.

Serial Port

The EFM32PG SoC has four USARTs and one Low Energy UART (LEUART).

Programming and Debugging

Note

Before using the kit the first time, you should update the J-Link firmware from J-Link-Downloads

Flashing

The EFM32PG-STK3402A includes an J-Link serial and debug adaptor built into the board. The adaptor provides:

• A USB connection to the host computer, which exposes a mass storage device and a USB serial port.

• A serial flash device, which implements the USB flash disk file storage.

• A physical UART connection which is relayed over interface USB serial port.

Flashing an application to EFM32PG-STK3402A

The sample application Hello World is used for this example. Build the Zephyr kernel and application:

# From the root of the zephyr repository
west build -b efm32pg_stk3402a samples/hello_world

Connect the EFM32PG-STK3402A to your host computer using the USB port and you should see a USB connection which exposes a mass storage device(STK3402A). Copy the generated zephyr.bin to the STK3402A drive.

Use a USB-to-UART converter such as an FT232/CP2102 to connect to the UART on the expansion header.

Open a serial terminal (minicom, putty, etc.) with the following settings:

• Speed: 115200

• Data: 8 bits

• Parity: None

• Stop bits: 1

Reset the board and you’ll see the following message on the corresponding serial port terminal session:

Hello World! arm