If you need urgent consulting help click here

96Boards Carbon nRF51

Overview

This is the secondary nRF51822 chip on the 96Boards Carbon and provides Bluetooth functionality to the main STM32F401RET chip via SPI.

Note

If you’re looking to reprogram the main STMicro part, see 96Boards Carbon. Users should not use this configuration unless they want to reprogram the secondary chip which provides Bluetooth connectivity.

Hardware

The 96Boards Carbon nRF51 has two external oscillators. The frequency of the slow clock is 32.768 kHz. The frequency of the main clock is 16 MHz.

See 96Boards Carbon for other general information about the board; that configuration is for the same physical board, just a different chip.

Supported Features

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

RTC

on-chip

system clock

UART

on-chip

serial port

GPIO

on-chip

gpio

FLASH

on-chip

flash

SPIS

on-chip

SPI slave

RADIO

on-chip

Bluetooth

The default configuration can be found in the defconfig file:

boards/arm/96b_carbon_nrf51/96b_carbon_nrf51_defconfig

Connections and IOs

SPI

96Boards Carbon nRF51 has one SPI, which for providing Bluetooth communication. The default SPI mapping for Zephyr is:

  • SPI1_NSS : P0.25

  • SPI1_SCK : P0.07

  • SPI1_MISO : P0.30

  • SPI1_MOSI : P0.00

The SWD debug pins are broken out to an external header; all other connected pins are to the main STM32F401RET chip.

Programming and Debugging

Flashing

The 96Boards Carbon nRF51 can be flashed using an external SWD debugger, via the debug header labeled “BLE” on the board’s silkscreen. The header is not populated; 0.1” male header must be soldered on first.

96Boards Carbon nRF51 Debug

Fig. 55 96Boards Carbon nRF51 Debug

The following example assumes a Zephyr binary zephyr.elf will be flashed to the board.

It uses the Black Magic Debug Probe as an SWD programmer, which can be connected to the BLE debug header using flying leads and its 20 Pin JTAG Adapter Board Kit. When plugged into your host PC, the Black Magic Debug Probe enumerates as a USB serial device as documented on its Getting started page.

It also uses the GDB binary provided with the Zephyr SDK, arm-zephyr-eabi-gdb. Other GDB binaries, such as the GDB from GCC ARM Embedded, can be used as well.

$ arm-zephyr-eabi-gdb -q zephyr.elf
(gdb) target extended-remote /dev/ttyACM0
Remote debugging using /dev/ttyACM0
(gdb) monitor swdp_scan
Target voltage: 3.3V
Available Targets:
No. Att Driver
 1      nRF51
(gdb) attach 1
Attaching to Remote target
0xabcdef12 in ?? ()
(gdb) load

Debugging

After you’ve flashed the chip, you can keep debugging using the same GDB instance. To reattach, just follow the same steps above, but don’t run “load”. You can then debug as usual with GDB. In particular, type “run” at the GDB prompt to restart the program you’ve flashed.

As an aid to debugging, this board configuration directs a console output to a currently unused pin connected to the STM32F401RET. Users who are experienced in electronics rework can remove a resistor (R22) on the board and attach a wire to the nRF51822’s UART output.

Providing Bluetooth to 96b_carbon

This 96b_carbon_nrf51 Zephyr configuration can be used to provide Bluetooth functionality from the secondary nRF51822 chip to the primary STM32F401RE chip on the 96Boards Carbon.

To do this, build the samples/bluetooth/hci_spi/ application provided with Zephyr with BOARD=96b_carbon_nrf51, then flash it to the nRF51822 chip using the instructions above. (For instructions on how to build a Zephyr application, see Building an Application.)

Warning

Be sure to flash the hci_spi application to the nRF51822 chip and not to the main STM32F401RET chip. While both chips are supported by Zephyr, the hci_spi application providing Bluetooth support will only run on the nRF51822 chip.