If you need urgent consulting help click here

96Boards Neonkey

Overview

96Boards Neonkey board is based on the STMicroelectronics STM32F411CE Cortex M4 CPU.

Fig. 56 96Boards Neonkey

This board acts as a sensor hub platform for all 96Boards compliant family products. It can also be used as a standalone board.

Hardware

96Boards Neonkey provides the following hardware components:

STM32F411CE in UFQFPN48 package
ARM® 32-bit Cortex®-M4 CPU with FPU
84 MHz max CPU frequency
1.8V work voltage
512 KB Flash
128 KB SRAM
On board sensors:
- Temperature/Humidity: SI7034-A10
- Pressure: BMP280
- ALS/Proximity: RPR-0521RS
- Geomagnetic: BMM150
- Accelerometer/Gyroscope: BMI160
- AMR Hall sensor: MRMS501A
- Microphone: SPK0415HM4H-B
4 User LEDs
15 General purpose LEDs
GPIO with external interrupt capability
I2C (3)
SPI (1)
I2S (1)

Supported Features

The Zephyr 96b_neonkey board configuration supports the following hardware features:

Interface	Controller	Driver/Component
NVIC	on-chip	nested vector interrupt controller
SYSTICK	on-chip	system clock
UART	on-chip	serial port
GPIO	on-chip	gpio
PINMUX	on-chip	pinmux
FLASH	on-chip	flash
SPI	on-chip	spi
I2C	on-chip	i2c

More details about the board can be found at 96Boards website.

The default board configuration can be found in the defconfig file:

boards/arm/96b_neonkey/96b_neonkey_defconfig

Connections and IOs

LED

LED1 / User1 LED = PB12
LED2 / User2 LED = PB13
LED3 / User3 LED = PB14
LED4 / User4 LED = PB15

Push buttons

BUTTON = RST (SW1)
BUTTON = USR (SW2)

System Clock

96Boards Neonkey can be driven by an internal oscillator as well as the main PLL clock. By default System clock is sourced by PLL clock at 84MHz, driven by internal oscillator.

Serial Port

On 96Boards Neonkey Zephyr console output is assigned to USART1. Default settings are 115200 8N1.

I2C

96Boards Neonkey board has up to 3 I2Cs. The default I2C mapping for Zephyr is:

I2C1_SCL : PB6
I2C1_SDA : PB7
I2C2_SCL : PB10
I2C2_SDA : PB3
I2C3_SCL : PA8
I2C3_SCL : PB4

SPI

96Boards Neonkey board has one SPI. The default SPI mapping for Zephyr is:

SPI1_NSS : PA4
SPI1_SCK : PA5
SPI1_MISO : PA6
SPI1_MOSI : PA7

Programming and Debugging

Building

Here is an example for building the Hello World application.

# From the root of the zephyr repository
west build -b 96b_neonkey samples/hello_world

Flashing

96Boards Neonkey can be flashed by two methods, one using the ROM bootloader and another using the SWD debug port (which requires additional hardware).

Using ROM bootloader:

ROM bootloader can be triggered by the following pattern:

Connect BOOT0 to VDD (link JTAG pins 1 and 5 on P4 header)
Press and hold the USR button
Press and release the RST button

More detailed information on activating the ROM bootloader can be found in Chapter 29 of Application note AN2606. The ROM bootloader supports flashing via UART, I2C and SPI protocols.

For flashing, stm32flash command line utility can be used. The following command will flash the zephyr.bin binary to the Neonkey board using UART and starts its execution:

$ stm32flash -w zephyr.bin -v -g 0x08000000 /dev/ttyS0

Note

The above command assumes that Neonkey board is connected to serial port /dev/ttyS0.

Using SWD debugger:

For flashing via SWD debug port, 0.1” male header must be soldered at P4 header available at the bottom of the board, near RST button.

Use the Black Magic Debug Probe as an SWD programmer, which can be connected to the P4 header using its flying leads and its 20 Pin JTAG Adapter Board Kit. When plugged into your host PC, the Black Magic Debug Probe enumerates as a USB serial device as documented on its Getting started page.

It also uses the GDB binary provided with the Zephyr SDK, arm-zephyr-eabi-gdb. Other GDB binaries, such as the GDB from GCC ARM Embedded, can be used as well.

$ arm-zephyr-eabi-gdb -q zephyr.elf
(gdb) target extended-remote /dev/ttyACM0
Remote debugging using /dev/ttyACM0
(gdb) monitor swdp_scan
Target voltage: 1.8V
Available Targets:
No. Att Driver
 1      STM32F4xx
(gdb) attach 1
Attaching to Remote target
0x080005d0 in ?? ()
(gdb) load

Debugging

After flashing 96Boards Neonkey, it can be debugged using the same GDB instance. To reattach, just follow the same steps above, till “attach 1”. You can then debug as usual with GDB. In particular, type “run” at the GDB prompt to restart the program you’ve flashed.