If you need urgent consulting help click here

ilitek,ili9340 (on spi bus)

Vendor: ILI Technology Corporation (ILITEK)

Description

ILI9340 320x240 display controller

Properties

Node specific properties

Deprecated node specific properties

Base properties

Properties not inherited from the base binding file.

Name	Type	Details
gamset	uint8-array	Gamma set (GAMSET) register value. Default value: [1]
frmctr1	uint8-array	Frame rate control (in normal mode / full colors) (FRMCTR1) register value. Default value: [0, 27]
disctrl	uint8-array	Display function control (DISCTRL) register value. Note that changing default SS bit value (0) may interfere with display rotation. Default value: [10, 130, 39]
pwctrl1	uint8-array	Power control 1 (PWCTRL1) register values. Default value: [38, 0]
pwctrl2	uint8-array	Power control 2 (PWCTRL2) register values. Default value: [0]
vmctrl1	uint8-array	VCOM control 1 (VMCTRL1) register values. Default value: [49, 60]
vmctrl2	uint8-array	VCOM control 2 (VMCTRL2) register values. Default value: [192]
pgamctrl	uint8-array	Positive gamma correction (PGAMCTRL) register values. Default value: [15, 34, 31, 10, 14, 6, 77, 118, 59, 3, 14, 4, 19, 14, 12]
ngamctrl	uint8-array	Negative gamma correction (NGAMCTRL) register values. Default value: [12, 35, 38, 4, 16, 4, 57, 36, 75, 3, 11, 11, 51, 55, 15]
reset-gpios	phandle-array	RESET pin. The RESET pin of ILI9340 is active low. If connected directly the MCU pin should be configured as active low.
cmd-data-gpios	phandle-array	D/CX pin. The D/CX pin of ILI9340 is active low (transmission command byte). If connected directly the MCU pin should be configured as active low. This property is required.
pixel-format	int	Display pixel format. Note that when RGB888 pixel format is selected only 6 color bits are actually used being in practice equivalent to RGB666. Legal values: 0, 1
rotation	int	Display rotation (CW) in degrees. Legal values: 0, 90, 180, 270
display-inversion	boolean	Display inversion mode. Every bit is inverted from the frame memory to the display.
spi-max-frequency	int	Maximum clock frequency of device's SPI interface in Hz This property is required.
duplex	int	Duplex mode, full or half. By default it's always full duplex thus 0 as this is, by far, the most common mode. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FULL_DUPLEX 2048 SPI_HALF_DUPLEX Legal values: 0, 2048
frame-format	int	Motorola or TI frame format. By default it's always Motorola's, thus 0 as this is, by far, the most common format. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FRAME_FORMAT_MOTOROLA 32768 SPI_FRAME_FORMAT_TI Legal values: 0, 32768
supply-gpios	phandle-array	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
vin-supply	phandle	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.
height	int	Height of the panel driven by the controller, with the units in pixels. This property is required.
width	int	Width of the panel driven by the controller, with the units in pixels. This property is required.

Deprecated properties not inherited from the base binding file.

(None)

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ilitek,ili9340” compatible.

Name	Type	Details
reg	array	register space This property is required. See Important properties for more information.
label	string	Human readable string describing the device (used as device_get_binding() argument) This property is required. See Important properties for more information.
status	string	indicates the operational status of a device Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss' See Important properties for more information.
compatible	string-array	compatible strings This property is required. See Important properties for more information.
reg-names	string-array	name of each register space
interrupts	array	interrupts for device See Important properties for more information.
interrupts-extended	compound	extended interrupt specifier for device
interrupt-names	string-array	name of each interrupt
interrupt-parent	phandle	phandle to interrupt controller node
clocks	phandle-array	Clock gate information
clock-names	string-array	name of each clock
#address-cells	int	number of address cells in reg property
#size-cells	int	number of size cells in reg property
dmas	phandle-array	DMA channels specifiers
dma-names	string-array	Provided names of DMA channel specifiers
io-channels	phandle-array	IO channels specifiers
io-channel-names	string-array	Provided names of IO channel specifiers
mboxes	phandle-array	mailbox / IPM channels specifiers
mbox-names	string-array	Provided names of mailbox / IPM channel specifiers
wakeup-source	boolean	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
power-domain	phandle	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.